These Forgefix Multi-Purpose Pozi Screws with countersunk heads have a zinc finish for increased durability. The screws are immensely popular and versatile, and used in all trades including joinery, electrical and plumbing. Also widely used in DIY applications. APPLICATIONSuitable for use with many materials including PVCu, Timber, Chipboard, MDF, and other similar types. Zinc coatings prevent oxidation of the protected metal to create a longer lasting finish. It does this by forming a barrier and by acting as a sacrificial anode if this barrier is damaged. Zinc oxide is a fine white dust that (in contrast to iron oxide) does not trigger a breakdown of the substrate’s surface integrity as it is formed. The zinc oxide, if left intact, can act as a barrier to further oxidation, in a way similar to the protection afforded to aluminium and stainless steels by their oxide layers. The Pozidriv screw is similar in appearance to the classic Phillips cross-head, but in fact is very different. The Pozidriv has four additional points of contact, and does not have the rounded corners that the Phillips screw drive has. The biggest advantage it offers is that, when used with the correct tooling in good condition, it does not cam out, allowing great torque to be applied. The Pozidriv screw can easily be distinguished by a line embossed in the screw head at 45° to the slots for the driver. The countersunk head is designed to sink flush with substrates to leave a smooth surface finish. They have single threads, designed to offer higher pull out values and quicker insertion.Specifications: Size: 3.5 x 30mm.Box quantity: 200.
These Forgefix Multi-Purpose Pozi Screws with countersunk heads are made from A2 stainless steel. They are ideal for use in and with many materials. APPLICATIONIdeal for use in sanitary locations and in marine environments. Stainless Steel does not corrode, rust or stain with water as ordinary steel does, but despite the name it is not fully stain-proof, most notably under low oxygen, high salinity, or poor circulation environments. Stainless steel is used where both the properties of steel and resistance to corrosion are required. The Pozidriv screw is similar in appearance to the classic Phillips cross-head, but in fact is very different. The Pozidriv has four additional points of contact, and does not have the rounded corners that the Phillips screw drive has. The biggest advantage it offers is that, when used with the correct tooling in good condition, it does not cam out, allowing great torque to be applied. The Pozidriv screw can easily be distinguished by a line embossed in the screw head at 45° to the slots for the driver. The screws' countersunk heads are designed to sink flush with substrates to leave a smooth surface finish. They have single threads, designed to offer higher pull out values and quicker insertion.Multi-Purpose Pozi Screw Countersunk ST Stainless Steel 4.0 x 30mm Box 200
These Forgefix High Tensile Hex Head Bolts are made from 8.8 grade steel. The bolts are part threaded and conform to DIN 933 standards. The hexagonal head has been designed for use with spanners or sockets and offers maximum torque when used with these tools. APPLICATION:For fastening together numerous types of material or to be fastened into pre-tapped holes. Widely used in many engineering applications. Zinc coatings prevent oxidation of the protected metal to create a longer lasting finish. It does this by forming a barrier and by acting as a sacrificial anode if this barrier is damaged. Zinc oxide is a fine white dust that (in contrast to iron oxide) does not trigger a breakdown of the substrate’s surface integrityHigh Tensile Bolts ZP M10 x 130 Bag 10
Heavy-Duty Clear Packaging Duck Tape® is a super strong tape for sealing, wrapping and securing parcels and packages. The tape is crystal clear and can also be used to laminate. Width: 50mmLength: 25m
ForgeFix TechFast Window Baypole screws are self-drilling screws which are suitable for joining bay window and other metal reinforced PVCu sections. They have a wafer head with TORX® compatible recess. Their No.3 drill tip allows self-drilling into steel up to 4mm.These screws are fire resistant and are protected by 'Elementech' corrosion resistant coating, which has been salt spray tested to 1000 hours. They comply with EU safety, health and environmental requirements. TX25 impact bit included.Size: 4.8 x 60mmPack: Box of 100
This Masterlock Endless Ratchet Tie Down includes Monster Weave™ strapping for durability and strength. The silver protectant finish not only delivers a richer appearance, but is also 3 times more corrosion resistant than standard webbing. TUV certified. Specification Length: 5mWidth: 25mmCapacity: Lashing: 400kg, Max.: 800kg
J-B Weld HighHeat trade; is a heat-resistant epoxy adhesive for bonding and gap filling substrates exposed to high temperatures up to 260 deg;C (500 deg;F). Resistant to water, chemicals and heat. Perfect for repairing vehicle exhausts, rust damage and other high heat automotive parts. It can be used on aluminium, brass, copper, iron and stainless steel. Specifications: Bonding Strength: 4,730 PSI.Set Time: 1 Hour.Cure Time: 24 Hours (room temp) or 1 Hour (with heat).Colour When Dry: Dark Grey.Size: 25ml.
Gorilla Super Glue Gel has a non-run control gel formula, allowing controlled application and making it ideal for use on vertical surfaces. The glue bonds in 10 seconds and is impact-tough. 1 x Gorilla Super Glue Gel 15g
Gorilla Contact Adhesive has a flexible, fast-setting, waterproof formula, making it suitable for both indoor and outdoor use. It forms a crystal clear, permanent bond. Bonds: metal, glass, fabric, wood, ceramic, leather, paper, rubber, plastic and more.
The Rapid EG380 Glue Gun is a powerful gun designed for industrial use, equipped with a 2 heater system with a total of 400 Watts providing a glue output of 2200 gr/hour. It is ideal for use on PVC, for sealing cables and tiles, electronics and electrics, furniture and wood, manual carton sealing, trade exhibits and decoration. It can be used for both low and high temperature 12mm diameter glue sticks and the temperature is adjustable from 130 to 230°C, the temperature settings are 130°C, 145°C, 170°C, 195°C and 230°C. Its strong feeding mechanism allows a higher glue output per trigger stroke for intensive use and it has a 4 minute heating time. Interchangeable nozzles (available to purchase separately) and an adjustable stand allow this glue gun to be used for all types of jobs. The smooth-4 finger soft grip trigger and ergonomic lightweight design ensures comfort over long term use and reduces the effort required. Comes with a 2 year guarantee. Specification Input Power: 400 Watt. Working Voltage: 220V-240 Volt.Heating Time: Less Than 2 Minutes (195°C). Temperature Settings: 130/145/170/195/230°C.Glue Output: 40g/min - 2200gr/hour.Glue Sticks: 12mm Glue Sticks.Regulation: Mechanical Thermostat.Nozzle: Ø 3.0mm. Cord Length: 3.5m.
The Faithfull 8mm Hook on a 50x50mm (2x2in) pre-drilled plate. Hook accessories should never be used for any overhead lifting or load bearing applications.This Faithfull Hook On Plate has a Galvanised finish for increased durability.
These ForgeFix traditional slotted, single thread Wood Screws have countersunk heads and can be used in many internal and external applications. They have a solid brass construction to avoid corrosion. APPLICATION:Used for both decorative and in applications where the screw may come in to contact with the elements avoiding corrosion.Can be used with all manner of wall plugs. Slotted screw driver required. With Slotted screwdrivers it is important to ensure that the tip matches the width of the screw slot, otherwise you run the risk of damaging the screw head. Slotted screwdrivers are available with either Flared or Parallel tips. For the majority of uses the Flared tip is ideal but if the screw needs to be driven below the material surface a Parallel tip screwdriver should be used. Countersunk heads are designed to sink flush with substrates to leave a smooth surface finish. The single threads have been designed to offer higher pull out values and quicker insertion.Wood Screw Slotted Countersunk Solid Brass 1.3/4 x 10 Box 200
Forgefix TechFast Bonded EPDM Washers provide a watertight seal. They offer protection against the weather, especially where moisture and condensation are a factor. The washer seals the hole created in the material being fixed and reduces the chance of corrosion. They are fire and corrosion resistant, protected by Elementech corrosion resistant coating, salt spray tested to 1000 hours. Comply with EU Safety, Health and Environmental requirements.These Forgefix TechFast Bonded EPDM Washers have the following specification: Size: 5.5 x 19mm
ForgeFix TechFast Window Baypole screws are self-drilling screws which are suitable for joining bay window and other metal reinforced PVCu sections. They have a wafer head with TORX® compatible recess. Their No.3 drill tip allows self-drilling into steel up to 4mm.These screws are fire resistant and are protected by 'Elementech' corrosion resistant coating, which has been salt spray tested to 1000 hours. They comply with EU safety, health and environmental requirements. TX25 impact bit included.Size: 4.8 x 70mmPack: Box of 100
These Forgefix Sleeve Anchors are through fixing, for ease of use and speed of installation. Their sleeve wedge cones are designed to give maximum expansion even in shallow anchoring depths. They have a reduced outside sleeve diameter compared to thread size for smaller hole sizes, offering reduced stress in base materials. The anchors are Zinc Yellow Passivated for increased corrosion resistace. They offer easier fixture removal or repositioning due to the bolt remaining in the shield. Also known as 'Projection Bolt' sleeve anchors. APPLICATIONWidely used for fixing balustrades, handrails, racking and holding down machinery, plus many more installation applications.Ensure the correct socket drive or spanner is used to ensure accurate installation. The Zinc Yellow Passivation process of electroplating is similar to the ‘Galvanised’ and ‘Zinc Plated’ processes but with the addition of a yellow dye. It provides a coating that is aesthetically pleasing, and which offers excellent resistance to corrosion.Sleeve Anchor Fixing Hex Nut M12 x 129 Bag 5
These Forgefix Masonry Anchor Projection Bolts have a Zinc Yellow Passivated finish for increased durability and resistance to corrosion. They have a tough and reliable construction to cover most heavy-duty fixing applications. The four-way expansion shield offers extremely strong and secure anchorage, and the specially manufactured retaining spring ensures encapsulation of the wedge during expansion. Projection bolts offer easier fixture removal or repositioning due to the bolt remaining in the shield. APPLICATION:Ideal for securing reinforcement wall plates, lighting supports, guy ropes and bracketry.Ensure the correct socket drive or spanner is used to ensure accurate installation. When sizing a Masonry Anchors it is most important to know the depth of the material that you are fixing.Eg: Size M610: The 'M6' is the thread size of the bolt. The '10' denotes the maximum thickness of material it will fix. The Zinc Yellow Passivation process of electroplating is similar to the ‘Galvanised’ and ‘Zinc Plated’ processes but with the addition of a yellow dye. It provides a coating that is aesthetically pleasing, and which offers excellent resistance to corrosion.Masonry Anchor Bolt Projecting Zinc Yellow Passivated M8 x 40 Bag 10
These Forgefix Masonry Anchor Projection Bolts have a Zinc Yellow Passivated finish for increased durability and resistance to corrosion. They have a tough and reliable construction to cover most heavy-duty fixing applications. The four-way expansion shield offers extremely strong and secure anchorage, and the specially manufactured retaining spring ensures encapsulation of the wedge during expansion. Projection bolts offer easier fixture removal or repositioning due to the bolt remaining in the shield. APPLICATION:Ideal for securing reinforcement wall plates, lighting supports, guy ropes and bracketry.Ensure the correct socket drive or spanner is used to ensure accurate installation. When sizing a Masonry Anchors it is most important to know the depth of the material that you are fixing.Eg: Size M610: The 'M6' is the thread size of the bolt. The '10' denotes the maximum thickness of material it will fix. The Zinc Yellow Passivation process of electroplating is similar to the ‘Galvanised’ and ‘Zinc Plated’ processes but with the addition of a yellow dye. It provides a coating that is aesthetically pleasing, and which offers excellent resistance to corrosion.Masonry Anchor Bolt Projecting Zinc Yellow Passivated M8 x 80 Bag 10
These ForgeFix Phillips Baypole Screws with wafer head are specifically designed for joining PVCu sections, particularly in bay windows. The nails have a self-drill tip and are zinc plated for increased corrosion resistance and durability. The wafer head distributes the load under the screw head, offering a firm positive fixing in a similar way to that of a washer. APPLICATION:The large wafer head distributes the load on numerous types of PVCu sections requiring joining. Zinc coatings prevent oxidation of the protected metal to create a longer lasting finish. It does this by forming a barrier and by acting as a sacrificial anode if this barrier is damaged. Zinc oxide is a fine white dust that (in contrast to iron oxide) does not trigger a breakdown of the substrate’s surface integrity as it is formed. The zinc oxide, if left intact, can act as a barrier to further oxidation, in a way similar to the protection afforded to aluminium and stainless steels by their oxide layers. The Phillips screw has four simple tapered slots. It is designed so that a Phillips tip screwdriver can turn a Phillips screw with increasing torque. When the torque gets too strong for the tip, the screwdriver tip winds itself out of the screw thus preventing over-tightening and or damage to the screw head. A self-drilling screw is similar to a sheet metal screw, but it has a drill-shaped point to cut through the substrate to eliminate the need for drilling a pilot hole. Designed for use in soft steel or other metals.Head: Wafer HeadFinish: Zinc PlatedSize: 4.8 x 100mmPack: Box 100
Top-quality 0.050 wire staples for T50 and T55 tackers. Made from stainless steel to resist rust. For use with T50, T55, T50PBN, HT50P, HTX50, ETFX50, ETF50PBN, CT50K, 5700 and 8000.The Arrow ARRT5012SS T50 Staples Stainless Steel 508SS comes in the following:Box Qty: 1000Size: 12mm - 1/2 inch
The Arrow RL100 riveter is made of an all steel construction with comfortable vinyl grip. The spring-loaded handle allows for easy rivet loading and ejection, with the changeable nosepiece taking a 1/8 diameter rivet in one hole, and 5/32 and 3/16 diameter in the other hole. To change hole size simply loosen screw on nosepiece plate, swing pivot plate around then re-tighten screw.Riveter only without any rivets supplied
Weller W101D Controlled Temperature Iron is suitable for a broad range of demanding soldering applications on electrical components with extremely high heat sensitivity. The industrial soldering irons of the W series have a solidly constructed heating element and a wide selection of long-life soldering tips. The tips are made of pure copper and are available with temperature ratings of 260°C, 316ºC, 425ºC and 480ºC. Temperature is controlled according to the Weller Magnastat principle. The metal cap that is firmly secured to the back of the soldering tip is the temperature sensor of this system; the Magnastat. The Magnastat system operates through a ferrous magnetic sensing device and is extremely stable, it does not deteriorate through ageing or metal fatigue. A further advantage of this design is that the soldering iron is completely switched off while the tip is being changed so that the heating element can not burn out in the absence of a tip. Specification: Watt: 100WVoltage: 230V
Forgefix TechFast Metal Roofing Panels to Timber Hex Screws are used to join metal roofing panels to timber frame buildings. They have a specially designed compression control thread to prevent damage and denting of panels. No pre-drilling is required and the self-drilling T17 Gash Point on screws makes for a rapid installation. The nails are fire and corrosion resistant, protected by Elementech corrosion resistant coating, salt spray tested to 1000 hours. Complies with EU Safety, Health and Environmental requirements. They are supplied with 16mm EPDM rubber washers.These Forgefix TechFast Metal Roofing to Timber Screws have the following specification: Size: 6.3 x 32mmSteel Thickness: 0.5-1.2mmHead Type: 8mm HexPack Size: 100
