These Forgefix Multi-Purpose Pozi Screws with countersunk heads are made from A2 stainless steel. They are ideal for use in and with many materials. APPLICATIONIdeal for use in sanitary locations and in marine environments. Stainless Steel does not corrode, rust or stain with water as ordinary steel does, but despite the name it is not fully stain-proof, most notably under low oxygen, high salinity, or poor circulation environments. Stainless steel is used where both the properties of steel and resistance to corrosion are required. The Pozidriv screw is similar in appearance to the classic Phillips cross-head, but in fact is very different. The Pozidriv has four additional points of contact, and does not have the rounded corners that the Phillips screw drive has. The biggest advantage it offers is that, when used with the correct tooling in good condition, it does not cam out, allowing great torque to be applied. The Pozidriv screw can easily be distinguished by a line embossed in the screw head at 45° to the slots for the driver. The screws' countersunk heads are designed to sink flush with substrates to leave a smooth surface finish. They have single threads, designed to offer higher pull out values and quicker insertion.Multi-Purpose Pozi Screw Countersunk ST Stainless Steel 3.5 x 30mm Box 200
These Forgefix Round Head Nails are multi-purpose nails, for use with both soft and hard timber materials. The nails have a 'Bright' finish, which is simply the basic raw mild steel material, without any coating or finish. APPLICATION:These nails are the most popular type of nail, used in many joinery and construction applications.Round Head Nail Bright Finish 40mm Bag of 2.5kg
These ForgeFix ForgeFast Wood Screws have a universally accepted, Pozi compatible drive. They have 6 underhead lobes for improved countersinking and reduced surface dust, and reinforced countersunk necks which improve holding power. The screws have an anti-friction thread for reduced splitting of the timber, reduced 'jacking' and spinning of joined timber and improved drawing strength. The thread is serrated for improved pull-out and reduced torque when inserting the screw. The double cutting point allows faster drilling time and reduced clogging of wood dust and is capable of piercing 0.8mm steel. The screws have an 'Elementech 400' coating providing an anti-corrosive metal finish, which lasts up to 6 times longer than standard zinc coatings. The coating is environmentally friendly and does not contain Cr6+. It is salt spray tested to 400 hours. The screws are suitable for interior and exterior use. Every tub is supplied with a Torx® compatible bit.Size: 4.0 x 30mm.Pack quantity: 1400.
These Forgefix Panel Pins are ideal for lightweight and decorative tasks. The shape of the pin helps to prevent splitting of hard or brittle timber.The nails have a 'Bright' finish, which is simply the basic raw mild steel material, without any coating or finish. APPLICATION:General cross section of joinery applications such as fixing decorative timber mouldings.Panel Pin Bright Finish 50mm Bag Weight 250g
These Forgefix Masonry Anchor Projection Bolts have a Zinc Yellow Passivated finish for increased durability and resistance to corrosion. They have a tough and reliable construction to cover most heavy-duty fixing applications. The four-way expansion shield offers extremely strong and secure anchorage, and the specially manufactured retaining spring ensures encapsulation of the wedge during expansion. Projection bolts offer easier fixture removal or repositioning due to the bolt remaining in the shield. APPLICATION:Ideal for securing reinforcement wall plates, lighting supports, guy ropes and bracketry.Ensure the correct socket drive or spanner is used to ensure accurate installation. When sizing a Masonry Anchors it is most important to know the depth of the material that you are fixing.Eg: Size M610: The 'M6' is the thread size of the bolt. The '10' denotes the maximum thickness of material it will fix. The Zinc Yellow Passivation process of electroplating is similar to the ‘Galvanised’ and ‘Zinc Plated’ processes but with the addition of a yellow dye. It provides a coating that is aesthetically pleasing, and which offers excellent resistance to corrosion.Masonry Anchor Bolt Projecting Zinc Yellow Passivated M12 x 75 Bag 5
These Forgefix Clout Nails have a large head, which distributes the load directly underneath the top of the nail, ensuring that roofing felt stays firm and secure. This reduces the risk of tearing. The nails are galvanised for increased resistance to corrosion.Suitable for roofing of all types. APPLICATION:Specifically used when roofing felt is being fitted to either shed or similar types of roofs. Galvanisation is process of applying a protective zinc coating to steel in order to prevent rusting. Zinc coatings prevent corrosion of the protected metal by forming a physical barrier, and by acting as a sacrificial anode even if this barrier is damaged.Clout Nail Galvanised 65mm Bag Weight 500g
The ForgeFast Decking Screws Reduced Head TORX® T15 are suitable for fixing into softwood or hardwood. They have a deep TORX® compatible insert that reduces cam-out, provides higher torque levels and a firmer drive. Its super sharp tip gives immediate bite from the very first turn. A patented self-drilling thread removes the need to pre-drill the timber and reduces the probability of splitting, even when screwing close to the edge. They have a hardened case and core to give exceptional strength with a reduced head size that provides discreet fixing and superb countersinking. Protected by elementech 2000 surface treatment which provides corrosion resistance up to 30 times longer than some standard zinc coated screws. They are highly resistant to pull out, they can flex by up to 35mm, reducing likelihood of screw shearing when used in flexible materials. CE approved for use in load-bearing timber construction.ForgeFast Decking Screws Reduced Head TORX T15 Size: 4.5 x 60mmPack Size: Tub of 500Finish: Tan elementech 2000
ForgeFix ForgeFast Wood Screws have a universally accepted, Torx® compatible drive. Their recessed ribs provide improved countersinking and reduced surface dust, and their reinforced countersunk necks improve holding power. The screws have a patented drill and drive thread for reduced splitting of the timber, reduced 'jacking' and spinning of joined timber, increased pull-out and a firmer fix. A sharp point provides faster bite and is capable of piercing 0.8mm steel. The screws have an 'Elementech 400' coating providing an anti-corrosive metal finish, which lasts up to 6 times longer than standard zinc coatings. The coating is environmentally friendly and does not contain Cr6+. It is Salt Spray tested to 400 hours. The screws are suitable for interior use. Every box is supplied with a Torx® compatible bit.Size: 6.0 x 180mm.Box quantity: 100.
ForgeFix ForgeFast Wood Screws have a universally accepted, Torx® compatible drive. Their recessed ribs provide improved countersinking and reduced surface dust, and their reinforced countersunk necks improve holding power. The screws have a patented drill and drive thread for reduced splitting of the timber, reduced 'jacking' and spinning of joined timber, increased pull-out and a firmer fix. A sharp point provides faster bite and is capable of piercing 0.8mm steel. The screws have an 'Elementech 400' coating providing an anti-corrosive metal finish, which lasts up to 6 times longer than standard zinc coatings. The coating is environmentally friendly and does not contain Cr6+. It is Salt Spray tested to 400 hours. The screws are suitable for interior use. Every box is supplied with a Torx® compatible bit.Size: 6.0 x 130mm.Box quantity: 100.
These Forgefix Multi-Purpose Pozi Screws with countersunk heads are made from A2 stainless steel. They are ideal for use in and with many materials. APPLICATIONIdeal for use in sanitary locations and in marine environments. Stainless Steel does not corrode, rust or stain with water as ordinary steel does, but despite the name it is not fully stain-proof, most notably under low oxygen, high salinity, or poor circulation environments. Stainless steel is used where both the properties of steel and resistance to corrosion are required. The Pozidriv screw is similar in appearance to the classic Phillips cross-head, but in fact is very different. The Pozidriv has four additional points of contact, and does not have the rounded corners that the Phillips screw drive has. The biggest advantage it offers is that, when used with the correct tooling in good condition, it does not cam out, allowing great torque to be applied. The Pozidriv screw can easily be distinguished by a line embossed in the screw head at 45° to the slots for the driver. The screws' countersunk heads are designed to sink flush with substrates to leave a smooth surface finish. They have single threads, designed to offer higher pull out values and quicker insertion.Multi-Purpose Pozi Screw Countersunk ST Stainless Steel 5.0 x 60mm Box 100
These Forgefix General Purpose Pozidrive Screws with Countersunk heads are zinc plated for increased durability. They are an extremely popular general purpose screw, and suitable for use in and with many materials. APPLICATION:Ideal for use in many ironmongery, electrical and plumbing applications.Can be used with various screw cover caps. Zinc coatings prevent oxidation of the protected metal to create a longer lasting finish. It does this by forming a barrier and by acting as a sacrificial anode if this barrier is damaged. Zinc oxide is a fine white dust that (in contrast to iron oxide) does not trigger a breakdown of the substrate’s surface integrity as it is formed. The zinc oxide, if left intact, can act as a barrier to further oxidation, in a way similar to the protection afforded to aluminium and stainless steels by their oxide layers. The Pozidriv screw is similar in appearance to the classic Phillips cross-head, but in fact is very different. The Pozidriv has four additional points of contact, and does not have the rounded corners that the Phillips screw drive has. The biggest advantage it offers is that, when used with the correct tooling in good condition, it does not cam out, allowing great torque to be applied. The Pozidriv screw can easily be distinguished by a line embossed in the screw head at 45° to the slots for the driver. The countersunk head is designed to sink flush with substrates to leave a smooth surface finish. They have twin threads, which enable an easy start when driving. Imperial Size > MetricNo.4 = 3.0mm, No.6 = 3.5mm, No.7 = 3.9mmNo.8= 4.0mm, No.10 = 5.0mm, No.12 = 6.0mmGeneral Purpose Pozi Screw Countersunk TT ZP 1.3/4 x 6 Box 200
These Forgefix TechFast Roofing Screws are designed for use in joining timber to steel and for heavy section purlins. They have a Torx, countersunk head to sit flush to the surface. The self-drilling point enables speedy insertion, and the wings create a clearance hole in the timber to eliminate the chance of 'jacking' when fixing. The screws are zinc plated and have an 'Elementech' coating for superior anti-corrosion, which has been salt spray tested to 1,000 hours. These heavy section roofing screws are suitable for fixing timber to steel thicknesses of 6.0mm to 12.5mm. Each pack is supplied with a free Torx bit.The TFCH5585 TechFast Roofing Screws have the following specifications: Size: 5.5 x 85mm.Pack quantity: 50.
These ForgeFix Don Quichotte Light Gauge Masonry Nails have the following specification: Size: 2.5 x 25mmFinish: Zinc GalvanisedPack Quantity: Box of 100
The ForgeFix Spectre Screws are advanced multipurpose wood screws with double countersunk heads and pozi compatible recess. They have a sawtooth thread design to prevent splitting and reamer to prevent jacking. The screws have a zinc yellow passivated finish for excellent resistance to corrosion. The zinc yellow passivation process of electroplating is similar to the 'galvanised' and 'zinc plated' processes but with the addition of a yellow dye. It offers an aesthetically pleasing finish.Specification: Size: 6.0 x 60mmThread: 36mm lengthPack Quantity: Box of 100
These Forgefix Sleeve Anchors are through fixing, for ease of use and speed of installation. Their sleeve wedge cones are designed to give maximum expansion even in shallow anchoring depths. They have a reduced outside sleeve diameter compared to thread size for smaller hole sizes, offering reduced stress in base materials. The anchors are Zinc Yellow Passivated for increased corrosion resistace. They offer easier fixture removal or repositioning due to the bolt remaining in the shield. Also known as 'Projection Bolt' sleeve anchors. APPLICATIONWidely used for fixing balustrades, handrails, racking and holding down machinery, plus many more installation applications.Ensure the correct socket drive or spanner is used to ensure accurate installation. The Zinc Yellow Passivation process of electroplating is similar to the ‘Galvanised’ and ‘Zinc Plated’ processes but with the addition of a yellow dye. It provides a coating that is aesthetically pleasing, and which offers excellent resistance to corrosion.Sleeve Anchor Fixing Hex Nut M10 x 97 Bag 10
ForgeFix Hex Head Lightning Bolts provide a virtually stress-free fixing for close to edge applications. They are self-threading and allow quick and easy installation of most masonry fixing applications. They can simply be screwed into a pre-drilled hole, without the need for a sleeve or plug. The bolts are through-fixing, eliminating the need for marking and re-positioning. They have a high load capacity due to the thread interlocking into the base material. The bolts have an 'Elementech' coating for superior anti-corrosion, which has been salt spray tested to 1,000 hours. Applications: Widely used for fixing battens, balustrades, handrails, racking and holding down machinery, plus many more installation applications. Suitable for most masonry substrates including concrete and brickwork but also for hollow block or bricks due to the nature of the thread type anchoring along the total length of the fixing.Specifications: Size: M16 x 100mm.Pack quantity: 10.
This ForgeFix ForgeFast Torx® Compatible Wood Screw Organiser contains a selection of the most popular sizes. With a universally accepted, Torx® compatible drive. Their recessed ribs provide improved countersinking and reduced surface dust, and their reinforced countersunk necks improve holding power. The patented drill and drive thread reduce splitting of the timber, reduced 'jacking' and spinning of joined timber, increased pull-out and a firmer fix. A sharp point provides faster bite and is capable of piercing 0.8mm steel. With an 'Elementech 400' coating providing an anti-corrosive metal finish which lasts up to 6 times longer than standard zinc coatings. The coating is environmentally friendly and does not contain Cr6+. It is Salt Spray tested to 400 hours. Contains: 150 x ForgeFast Torx® Compatible Wood Screws ZY 3.5 x 16mm.100 x ForgeFast Torx® Compatible Wood Screws ZY 3.5 x 25mm.180 x ForgeFast Torx® Compatible Wood Screws ZY 3.5 x 30mm.130 x ForgeFast Torx® Compatible Wood Screws ZY 4.0 x 25mm.140 x ForgeFast Torx® Compatible Wood Screws ZY 4.0 x 30mm.100 x ForgeFast Torx® Compatible Wood Screws ZY 4.0 x 40mm.80 x ForgeFast Torx® Compatible Wood Screws ZY 4.0 x 50mm.55 x ForgeFast Torx® Compatible Wood Screws ZY 5.0 x 50mm.65 x ForgeFast Torx® Compatible Wood Screws ZY 5.0 x 80mm.
These ForgeFix Don Quichotte Heavy Gauge Masonry Nails have the following specification: Size: 3.5 x 70mmFinish: Zinc GalvanisedPack Quantity: Box of 100
The Arrow P35 Plier Type Stapler is a more powerful, heavy-duty version of the P22. It has a steel construction with a powerful drive for accommodating tougher materials. Designed for reaching into hard to get at places for stapling from any position or angle. Ideal for sealing and bagging applications. Fires: P35 staples 6-8mm.
These Forgefix General Purpose Pozidrive Screws with Countersunk heads are zinc plated for increased durability. They are an extremely popular general purpose screw, and suitable for use in and with many materials. APPLICATION:Ideal for use in many ironmongery, electrical and plumbing applications.Can be used with various screw cover caps. Zinc coatings prevent oxidation of the protected metal to create a longer lasting finish. It does this by forming a barrier and by acting as a sacrificial anode if this barrier is damaged. Zinc oxide is a fine white dust that (in contrast to iron oxide) does not trigger a breakdown of the substrate’s surface integrity as it is formed. The zinc oxide, if left intact, can act as a barrier to further oxidation, in a way similar to the protection afforded to aluminium and stainless steels by their oxide layers. The Pozidriv screw is similar in appearance to the classic Phillips cross-head, but in fact is very different. The Pozidriv has four additional points of contact, and does not have the rounded corners that the Phillips screw drive has. The biggest advantage it offers is that, when used with the correct tooling in good condition, it does not cam out, allowing great torque to be applied. The Pozidriv screw can easily be distinguished by a line embossed in the screw head at 45° to the slots for the driver. The countersunk head is designed to sink flush with substrates to leave a smooth surface finish. They have twin threads, which enable an easy start when driving. Imperial Size > MetricNo.4 = 3.0mm, No.6 = 3.5mm, No.7 = 3.9mmNo.8= 4.0mm, No.10 = 5.0mm, No.12 = 6.0mmGeneral Purpose Pozi Screw Countersunk TT ZP 3/4 x 10 Box 200
Bostik Soft Plastic Clear Adhesive ia a strong, water-resistant clear adhesive, suitable for most soft plastics. Extra strong bond, supplied with PVC repair patch. Type: Soft plastic.Size. 20ml.
Powder Mortar Tone is formulated from best quality oxide pigments for permanently colouring all types of mortars, rendering, concrete and pointing. The pigments disperse easily into the mix to give a uniform shade for each mix batch. Shading can be adjusted to provide a wider variety of colour depths. Permanently colours cement based products - light fast pigments will not fade.Improves workability/trowelability - contains a plasticizer.Chloride free (chloride ion content < 0.1%).Reduces bleeding/segregation.Inhibits efflorescence.
Everbuild STICK2® Hard Plastic Adhesive is a strong, clear, quick drying adhesive, suitable for bonding most hard plastics such as rigid PVC, acrylic, polycarbonate and ABS. Ideal for repairs to guttering, sills and bonding PVCu and ABS non-pressure pipework. Temperature resistant to 100°C.
The Shurtape Original Cloth Duck Tape® is ideal for fixing, binding, repairing, protecting, identifying and reinforcing tasks. It is strong, waterproof, tears easily and is for use both indoors and out. Ideal for hundreds of uses around the home, garage and garden with high strength adhesive - sticks firmly to most surfaces. Not suitable for total immersion in water.This Duck Tape® Original comes in the following: Colour: BlackWidth: 50mm (2in)Length: 25m
A one-part contact adhesive ideal for numerous jobs around the home and in the workshop. Provides a High strength strong bond on contact without the need for special support, jigs, clamps or weights. Suitable for bonding many types of substrates. Multi-purpose - the ideal adhesive for emergency repairs.Bonds most materials even non-porous e.g metals.Size Small Tube 30g
Bostik Fast Tak is a strong aerosol adhesive that allows for repositioning. Clear, fast setting, non-staining adhesive for paper. Convenient spray application for larger areas. Ideal for household repairs, craft and much more.1 x Bostik Fast Tak Contact Adhesive Spray 500ml
These Faithfull welded steel chains are made with the link side welded for extra strength. They have mild steel welded straight links made to form an A style short link chain. The chains are bright zinc plated and ideal for general purpose applications such as securing loads. Maximum load figures quoted are for guidance only. These chains are test load tested, but not certified and should never be used for any overhead lifting, load binding or towing applications.The Faithfull FAICHAL615 A link chain has the following dimensions:Thickness: 6mmLength: 15m
The Faithfull 6mm Staple on a 50 x 50mm (2 x 2in) pre-drilled plate. Multipurpose product for use with lengths of chain, to provide security on sheds, shutter doors, gates etc..This Faithfull Staple On Plate has a ;Black Japanned finish for increased durability.
These ForgeFix ForgeFast Wood Screws have a universally accepted, Pozi compatible drive. They have 6 underhead lobes for improved countersinking and reduced surface dust, and reinforced countersunk necks which improve holding power. The screws have an anti-friction thread for reduced splitting of the timber, reduced 'jacking' and spinning of joined timber and improved drawing strength. The thread is serrated for improved pull-out and reduced torque when inserting the screw. The double cutting point allows faster drilling time and reduced clogging of wood dust and is capable of piercing 0.8mm steel. The screws have a 'Elementech 400' coating providing an anti-corrosive metal finish, which lasts up to 6 times longer than standard zinc coatings. The coating is environmentally friendly and does not contain Cr6+. It is Salt Spray tested to 400 hours. The screws are suitable for interior use.Size: 5.0 x 60mm.Box quantity: 100.
These Forgefix General Purpose Pozidrive Screws with Countersunk heads are zinc plated for increased durability. They are an extremely popular general purpose screw, and suitable for use in and with many materials. APPLICATION:Ideal for use in many ironmongery, electrical and plumbing applications.Can be used with various screw cover caps. Zinc coatings prevent oxidation of the protected metal to create a longer lasting finish. It does this by forming a barrier and by acting as a sacrificial anode if this barrier is damaged. Zinc oxide is a fine white dust that (in contrast to iron oxide) does not trigger a breakdown of the substrate’s surface integrity as it is formed. The zinc oxide, if left intact, can act as a barrier to further oxidation, in a way similar to the protection afforded to aluminium and stainless steels by their oxide layers. The Pozidriv screw is similar in appearance to the classic Phillips cross-head, but in fact is very different. The Pozidriv has four additional points of contact, and does not have the rounded corners that the Phillips screw drive has. The biggest advantage it offers is that, when used with the correct tooling in good condition, it does not cam out, allowing great torque to be applied. The Pozidriv screw can easily be distinguished by a line embossed in the screw head at 45° to the slots for the driver. The countersunk head is designed to sink flush with substrates to leave a smooth surface finish. They have twin threads, which enable an easy start when driving. Imperial Size > MetricNo.4 = 3.0mm, No.6 = 3.5mm, No.7 = 3.9mmNo.8= 4.0mm, No.10 = 5.0mm, No.12 = 6.0mmGeneral Purpose Pozi Screw Countersunk TT ZP 1.3/4 x 8 Box 200
These Forgefix General Purpose Pozidrive Screws with Countersunk heads are zinc plated for increased durability. They are an extremely popular general purpose screw, and suitable for use in and with many materials. APPLICATION:Ideal for use in many ironmongery, electrical and plumbing applications.Can be used with various screw cover caps. Zinc coatings prevent oxidation of the protected metal to create a longer lasting finish. It does this by forming a barrier and by acting as a sacrificial anode if this barrier is damaged. Zinc oxide is a fine white dust that (in contrast to iron oxide) does not trigger a breakdown of the substrate’s surface integrity as it is formed. The zinc oxide, if left intact, can act as a barrier to further oxidation, in a way similar to the protection afforded to aluminium and stainless steels by their oxide layers. The Pozidriv screw is similar in appearance to the classic Phillips cross-head, but in fact is very different. The Pozidriv has four additional points of contact, and does not have the rounded corners that the Phillips screw drive has. The biggest advantage it offers is that, when used with the correct tooling in good condition, it does not cam out, allowing great torque to be applied. The Pozidriv screw can easily be distinguished by a line embossed in the screw head at 45° to the slots for the driver. The countersunk head is designed to sink flush with substrates to leave a smooth surface finish. They have twin threads, which enable an easy start when driving. Imperial Size > MetricNo.4 = 3.0mm, No.6 = 3.5mm, No.7 = 3.9mmNo.8= 4.0mm, No.10 = 5.0mm, No.12 = 6.0mmGeneral Purpose Pozi Screw Countersunk TT ZP 5/8 x 4 Box 200
These Forgefix Annular Ring Shank Nails are ideal for where strength and holding power are of primary importance. The rings on the shank of the nail are sloped in a conical shape to ensure clean insertion but are then extremely difficult to release. They are suitable for both soft and hard wood. The nails have a 'Bright' finish, which is simply the basic raw mild steel material, without any coating or finish. APPLICATION:Used where permanent holding is preferred such as flooring applications.Annular Ring Shank Nail Bright 40mm Bag Weight 500g
These ForgeFix ForgeFast Wood Screws have a universally accepted, Pozi compatible drive. They have 6 underhead lobes for improved countersinking and reduced surface dust, and reinforced countersunk necks which improve holding power. The screws have an anti-friction thread for reduced splitting of the timber, reduced 'jacking' and spinning of joined timber and improved drawing strength. The thread is serrated for improved pull-out and reduced torque when inserting the screw. The double cutting point allows faster drilling time and reduced clogging of wood dust and is capable of piercing 0.8mm steel. The screws have a 'Elementech 400' coating providing an anti-corrosive metal finish, which lasts up to 6 times longer than standard zinc coatings. The coating is environmentally friendly and does not contain Cr6+. It is Salt Spray tested to 400 hours. The screws are suitable for interior use.Size: 5.0 x 100mm.Box quantity: 100.
