Forgefix TechFast Roofing Sheets to Steel Hex Screws are used for joining metal roofing panels to steel frame buildings. The screws are fire resistant and corrosion resistant. Protected by Elementech corrosion resistant coating, salt spray tested to 1000 hours. Complies with EU Safety, Health and Environmental requirements. They are supplied with 16mm EPDM rubber washers.These Forgefix TechFast Roofing Sheets to Steel Hex Screws have the following specification: Size: 5.5 x 75mmEffective Thread Length: 58mmPack Size: 100Drill Tip: No.3 No.3 drill tip for self-drilling in heavy gauge steel up to 5mm.
ForgeFix ForgeFast Wood Screws have a universally accepted, Torx® compatible drive. Their recessed ribs provide improved countersinking and reduced surface dust, and their reinforced countersunk necks improve holding power. The screws have a patented drill and drive thread for reduced splitting of the timber, reduced 'jacking' and spinning of joined timber, increased pull-out and a firmer fix. A sharp point provides faster bite and is capable of piercing 0.8mm steel. The screws have an 'Elementech 400' coating providing an anti-corrosive metal finish, which lasts up to 6 times longer than standard zinc coatings. The coating is environmentally friendly and does not contain Cr6+. It is Salt Spray tested to 400 hours. The screws are suitable for interior use. Every tub is supplied with a Torx® compatible bit.Size: 5.0 x 90mm.Pack quantity: 350.
Forgefix Countersunk Torx® Compatible Head Lightening Bolts provide a virtually stress free fixing for close to edge applications. They are self-threading and allow quick and easy installation of most masonry fixing applications. They can simply be screwed into a pre-drilled hole, without the need for a sleeve or plug. The bolts are through-fixing, eliminating the need for marking and re-positioning. They have a high load capacity due to the thread interlocking into the base material. The Torx® compatible head provides increased control, and is countersunk to sit flush to the surface of the material. The bolts have an 'Elementech' coating for superior anti-corrosion, which has been salt spray tested to 1,000 hours. Applications: Widely used for fixing battens, balustrades, handrails, racking and holding down machinery, plus many more installation applications. Suitable for most masonry substrates including concrete and brickwork but also for hollow block or bricks due to the nature of the thread type anchoring along the total length of the fixing.Specifications:Size: M6 x 75mm.Bag of 10.
These Forgefix Double Cliplock Pipe Clips are made from heat-resistant polypropylene, designed to withstand the temperature changes in central heating systems, and are effective with temperatures of up to 100°C (most pipes in domestic central heating systems operate at around 70°C). APPLICATION:Used when fitting most types of pipe work. Polypropylene, also known as polypropene, is a thermoplastic polymer used in a wide variety of applications. An addition polymer made from the monomer propylene, it is rugged and unusually resistant to many chemical solvents, bases and acids.Pipe Clip Double Cliplock 15mm Box 50
ForgeFix ForgeFast Wood Screws have a universally accepted, Torx® compatible drive. Their recessed ribs provide improved countersinking and reduced surface dust, and their reinforced countersunk necks improve holding power. The screws have a patented drill and drive thread for reduced splitting of the timber, reduced 'jacking' and spinning of joined timber, increased pull-out and a firmer fix. A sharp point provides faster bite and is capable of piercing 0.8mm steel. The screws have an 'Elementech 400' coating providing an anti-corrosive metal finish, which lasts up to 6 times longer than standard zinc coatings. The coating is environmentally friendly and does not contain Cr6+. It is Salt Spray tested to 400 hours. The screws are suitable for interior use. Every box is supplied with a Torx® compatible bit.Size: 3.5 x 12mm.Box quantity: 200.
The ForgeFast Decking Screws Countersunk TORX® T25 are suitable for fixing into softwood or hardwood. They have a deep TORX® compatible insert that reduces cam-out, provides higher torque levels and a firmer drive. Its super sharp tip gives immediate bite from the very first turn and the recessed under-head ribs provide superb countersinking. A patented self-drilling thread removes the need to pre-drill the timber and reduces the probability of splitting, even when screwing close to the edge. Protected by elementech 2000 surface treatment which provides corrosion resistance up to 30 times longer than some standard zinc coated screws. They are highly resistant to pull out, they can flex by up to 35mm, reducing likelihood of screw shearing when used in flexible materials. CE approved for use in load-bearing timber construction.ForgeFast Decking Screws Countersunk TORX® T25 Size: 5.0 x 100mmPack Size: Tub of 300Finish: Green elementech 2000
These Forgefix Felt Nails have a large head, which distributes the load directly underneath the top of the nail, ensuring that roofing felt stays firm and secure. This reduces the risk of tearing. The nails are galvanised for increased resistance to corrosion.Suitable for roofing of all types. APPLICATION:Specifically used when roofing felt is being fitted to either shed or similar types of roofs. Galvanisation is process of applying a protective zinc coating to steel in order to prevent rusting. Zinc coatings prevent corrosion of the protected metal by forming a physical barrier, and by acting as a sacrificial anode even if this barrier is damaged.Felt Nail Galvanised 13mm Bag Weight 2.5kg
These Forgefix Pozidriv Self-Tapping Screws have countersunk heads and are Zinc Plated for increased resistance to corrosion. They tap their own thread in to a pre-drilled pilot hole in sheet or solid material. They are single threaded to resist pull-out. APPLICATION:Ideal for use in many DIY, ironmongery, engineering, electrical and plumbing applications. Zinc coatings prevent oxidation of the protected metal to create a longer lasting finish. It does this by forming a barrier and by acting as a sacrificial anode if this barrier is damaged. Zinc oxide is a fine white dust that (in contrast to iron oxide) does not trigger a breakdown of the substrate’s surface integrity as it is formed. The zinc oxide, if left intact, can act as a barrier to further oxidation, in a way similar to the protection afforded to aluminium and stainless steels by their oxide layers. The Pozidriv screw is similar in appearance to the classic Phillips cross-head, but in fact is very different. The Pozidriv has four additional points of contact, and does not have the rounded corners that the Phillips screw drive has. The biggest advantage it offers is that, when used with the correct tooling in good condition, it does not cam out, allowing great torque to be applied. The Pozidriv screw can easily be distinguished by a line embossed in the screw head at 45° to the slots for the driver. Countersunk heads are designed to sink flush with substrates to leave a smooth surface finish.Self Tapping Screw Pozi Countersunk ZP 3/4 x 8 Box 200
These Forgefix Oval Lost Head Nails are versatile and ideal for use in general joinery. The nail head virtually disappears when punched below the timber surface, making them ideal for decorative type applications. The shape of the nail helps to prevent splitting of hard or brittle timber. The nails have a 'Bright' finish, which is simply the basic raw mild steel material, without any coating or finish. APPLICATION:General cross section of joinery applications. By aligning the nail with the wood grain, splitting is reduced.Oval Lost Head Nail Bright 75mm Bag Weight 500g
These ForgeFix Phillips Baypole Screws with wafer head are specifically designed for joining PVCu sections, particularly in bay windows. The nails have a self-drill tip and are zinc plated for increased corrosion resistance and durability. The wafer head distributes the load under the screw head, offering a firm positive fixing in a similar way to that of a washer. APPLICATION:The large wafer head distributes the load on numerous types of PVCu sections requiring joining. Zinc coatings prevent oxidation of the protected metal to create a longer lasting finish. It does this by forming a barrier and by acting as a sacrificial anode if this barrier is damaged. Zinc oxide is a fine white dust that (in contrast to iron oxide) does not trigger a breakdown of the substrate’s surface integrity as it is formed. The zinc oxide, if left intact, can act as a barrier to further oxidation, in a way similar to the protection afforded to aluminium and stainless steels by their oxide layers. The Phillips screw has four simple tapered slots. It is designed so that a Phillips tip screwdriver can turn a Phillips screw with increasing torque. When the torque gets too strong for the tip, the screwdriver tip winds itself out of the screw thus preventing over-tightening and or damage to the screw head. A self-drilling screw is similar to a sheet metal screw, but it has a drill-shaped point to cut through the substrate to eliminate the need for drilling a pilot hole. Designed for use in soft steel or other metals.Head: Wafer HeadFinish: Zinc PlatedSize: 4.8 x 60mmPack: Box 100
These Forgefix Multi-Purpose Pozi Screws with countersunk heads have a zinc yellow passivated finish for increased durability. The screws are immensely popular and versatile, and used in all trades including joinery, electrical and plumbing. Also widely used in DIY applications. APPLICATIONSuitable for use with many materials including PVCu, Timber, Chipboard, MDF, and other similar types. The Zinc Yellow Passivation process of electroplating is similar to the 'Galvanised' and 'Zinc Plated' processes but with the addition of a yellow dye. It offers an aesthetically pleasing finish, whilst having excellent resistance to corrosion. The Pozidriv screw is similar in appearance to the classic Phillips cross-head, but in fact is very different. The Pozidriv has four additional points of contact, and does not have the rounded corners that the Phillips screw drive has. The biggest advantage it offers is that, when used with the correct tooling in good condition, it does not cam out, allowing great torque to be applied. The Pozidriv screw can easily be distinguished by a line embossed in the screw head at 45° to the slots for the driver. The countersunk head is designed to sink flush with substrates to leave a smooth surface finish. They have single threads, designed to offer higher pull out values and quicker insertion.Multi-Purpose Pozi Screw Countersunk ST ZYP 3.0 x 25mm Box 200
ForgeFix ForgeFast Wood Screws have a universally accepted, Torx® compatible drive. Their recessed ribs provide improved countersinking and reduced surface dust, and their reinforced countersunk necks improve holding power. The screws have a patented drill and drive thread for reduced splitting of the timber, reduced 'jacking' and spinning of joined timber, increased pull-out and a firmer fix. A sharp point provides faster bite and is capable of piercing 0.8mm steel. The screws have an 'Elementech 400' coating providing an anti-corrosive metal finish, which lasts up to 6 times longer than standard zinc coatings. The coating is environmentally friendly and does not contain Cr6+. It is Salt Spray tested to 400 hours. The screws are suitable for interior use. Every tub is supplied with a Torx® compatible bit.Size: 4.0 x 70mm.Pack quantity: 600.
This ForgeFix ForgeFast Torx® Compatible Wood Screw Pack contains a selection of the most popular sizes of professional, high performance multi purpose woodscrews. With a universally accepted, Torx® compatible drive. Their recessed ribs provide improved countersinking and reduced surface dust, and their reinforced countersunk necks improve holding power.The patented drill and drive thread reduce splitting of the timber, reduced 'jacking' and spinning of joined timber, increased pull-out and a firmer fix. A sharp point provides faster bite and is capable of piercing 0.8mm steel.With an 'Elementech 400' coating providing an anti-corrosive metal finish which lasts up to 6 times longer than standard zinc coatings. The coating is environmentally friendly and does not contain Cr6+. It is Salt Spray tested to 400 hours.Contains:1 x Box of 200 ForgeFast Torx® Compatible Wood Screws ZY 3.0 x 25mm.1 x Box of 200 ForgeFast Torx® Compatible Wood Screws ZY 3.5 x 30mm.1 x Box of 200 ForgeFast Torx® Compatible Wood Screws ZY 3.5 x 40mm.1 x Box of 200 ForgeFast Torx® Compatible Wood Screws ZY 4.0 x 30mm.1 x Box of 200 ForgeFast Torx® Compatible Wood Screws ZY 4.0 x 40mm.1 x Box of 200 ForgeFast Torx® Compatible Wood Screws ZY 4.0 x 50mm.1 x Box of 200 ForgeFast Torx® Compatible Wood Screws ZY 5.0 x 50mm.1 x Box of 100 ForgeFast Torx® Compatible Wood Screws ZY 5.0 x 60mm.1 x Box of 100 ForgeFast Torx® Compatible Wood Screws ZY 5.0 x 70mm.1 x Box of 100 ForgeFast Torx® Compatible Wood Screws ZY 5.0 x 80mm.1 x Box of 100 ForgeFast Torx® Compatible Wood Screws ZY 5.0 x 100mm.
The ForgeFix Spectre Screws are advanced multipurpose wood screws with double countersunk heads and pozi compatible recess. They have a sawtooth thread design to prevent splitting and reamer to prevent jacking. The screws have a zinc yellow passivated finish for excellent resistance to corrosion. The zinc yellow passivation process of electroplating is similar to the 'galvanised' and 'zinc plated' processes but with the addition of a yellow dye. It offers an aesthetically pleasing finish.Specification: Size: 4.5 x 70mmThread: 42mm lengthPack Quantity: Box of 100
These ForgeFix Don Quichotte Light Gauge Masonry Nails have the following specification: Size: 2.5 x 35mmFinish: Zinc GalvanisedPack Quantity: Box of 100
Command™ Micro Hooks provide an innovative solution for hanging lightweight objects, such as calendars and keys, securely and damage-free. 3M stretch-release technology provides a strong hold and removes cleanly. They’re easy to apply and remove - leaving no holes, marks or sticky residue. Rehanging them is as easy as applying a Command™ Refill Strip, so you can take down, move and reuse them again and again. Suitable for a wide variety of surfaces; solid, hollow and painted walls, as well as other materials including wood, tile, metal and glass. Contains: 3 x White Micro Hooks (hold up to 225g per hook)4 x Refill Strips
This Energizer® LED Golf Non-Dimmable Bulb has the following specification: Fitting: BC (B22)Input Wattage: 5.9W (40W equivalent)Lumens of Light: 470 lmSwitching Cycles: 40,000Average Rated Life: 15,000 hoursColour Temperature: 2,700K (Warm White)Lamp Dimensions: 45 x 87mmDimmable: NoRated: A+
This Energizer® LED Opal GLS Non-Dimmable Bulb has the following specification: Fitting: ES (E27)Input Wattage: 9.2W (60W equivalent)Lumens of Light: 806 lmSwitching Cycles: 40,000Average Rated Life: 15,000 hoursColour Temperature: 2,700K (Warm White)Lamp Dimensions: 60 x 110mmDimmable: NoRated: A+
This Energizer® LED Candle Non-Dimmable Bulb has the following specification: Fitting: BC (B22)Input Wattage: 3.4W (25W equivalent)Lumens of Light: 250 lmSwitching Cycles: 40,000Average Rated Life: 15,000 hoursColour Temperature: 2,700K (Warm White)Lamp Dimensions: 35 x 98mmDimmable: NoRated: A+
Unibond Powertape is a multi-purpose tape that uses 3 'Power Layers' to form an outstanding heavy-duty, fabric reinforced tape. It is 100% waterproof and even sticks to wet surfaces. Powertape is ideal for temporary repair to guttering, children's paddling pools and tents. This heavy-duty adhesive tape has hundreds of uses around the home, car and garden and is suitable for both interior and exterior use. There is no need for scissors as the tape is easily torn by hand.Size: 50mm x 25m. Colour: Silver.
1 x Loctite Super Glue Power Gel Tube 20g. Loctite Super Glue Power Gel is formulated with cyanoacrylate rubber-infused gel formula, this instant glue allows powerful bonds which are extremely precise even on vertical surfaces and materials requiring high flexibility. Strong resistance with instant strength in a single drop, this super glue ensures durability whilst drying transparently. This multi material glue works on a variety of materials: wood, rubber, plastic* and more. It even works as a leather glue. The adhesive not only withstands strong conditions but is also shock resistant, waterproof and heatproof. Before starting, ensure the surfaces you want to bond are clean, dry and close-fitting. Simply remove the cap and apply a small quantity of the power glue gel to one surface, press both surfaces together immediately and hold them in place until the bond sets. Simple! *except polyethylene (PE) or polypropylene (PP). 20g
Thompson's Emergency Leak Fix is a high-performance clear sealant, which seals and repairs virtually any exterior surface, providing a long-lasting, highly durable waterproof repair. The unique formulation adheres to most surfaces, even in damp conditions, to form a waterproof seal that remains flexible over time protecting against cracking and splitting. Ideal for sealing doors and windows, the unique formula has been developed to be over-painted with solvent-based or water-based paints and stains. Usage Areas: wood, painted surfaces, glass, PVCu, plastics, brickwork, stone, roof felt, slate, tile and zinc.
These Forgefix Pozidriv Self-Tapping Screws are zinc plated for increased resistance to corrosion. Their Pan Head, with a flat under head surface makes the screw ideal to lay flat on sheet material of all types, thus reducing deformation. The screws tap their own thread in a pre-drilled pilot hole, in sheet metal. The screws are single threaded to resist pull-out. APPLICATIONIdeal for use in many DIY, ironmongery, engineering, electrical and plumbing applications. Zinc coatings prevent oxidation of the protected metal to create a longer lasting finish. It does this by forming a barrier and by acting as a sacrificial anode if this barrier is damaged. Zinc oxide is a fine white dust that (in contrast to iron oxide) does not trigger a breakdown of the substrate’s surface integrity as it is formed. The zinc oxide, if left intact, can act as a barrier to further oxidation, in a way similar to the protection afforded to aluminum and stainless steels by their oxide layers. The Pozidriv screw is similar in appearance to the classic Phillips cross-head, but in fact is very different. The Pozidriv has four additional points of contact, and does not have the rounded corners that the Phillips screw drive has. The biggest advantage it offers is that, when used with the correct tooling in good condition, it does not cam out, allowing great torque to be applied. The Pozidriv screw can easily be distinguished by a line embossed in the screw head at 45° to the slots for the driver.Self Tapping Screw Pozi Pan Head ZP 1 x 8 Box 200
These Forgefix Twist Nails are a unique twisted shank nail for attaching metalwork joists, hangers, straps etc. The twisted shank assists in absorbing movement that may occur in construction. They have a sheradised finish for corrosion resistance. This finish is a thermal diffusion process, in which Zinc powder is vaporised and diffuses to the surface of the Twist Nail to form a sacrificial corrosion protective Zinc/Iron alloy coating, thus dramatically increasing the nails' durability. APPLICATION:The Twist Nail is the most popular construction nail used in fixing of joist hangers, restraining straps and Galvanised banding.Twist Nails Sheradised 30mm Bag Weight 500g
These Forgefix Through Bolts (also known as Wedge Anchors or Toothless Anchors) have a Zinc Yellow Passivated finish for durability and corrosion resistance. They are through-fixing, and extremely economical and quick to install. APPLICATIONIdeal for fixing brackets, cladding, restraints, racking, fabricated stairwells and industrial doors.Ensure the correct socket drive or spanner is used to ensure accurate installation. The Zinc Yellow Passivation process of electroplating is similar to the Galvanised and Zinc Plated processes but with the addition of a yellow dye. It provides a coating that is aesthetically pleasing, and which offers excellent resistance to corrosion.Through Bolt Zinc Yellow Passivated M8 x 95 Bag 10
These Forgefix Multi-Purpose Pozi Screws with countersunk heads have a zinc finish for increased durability. The screws are immensely popular and versatile, and used in all trades including joinery, electrical and plumbing. Also widely used in DIY applications. APPLICATIONSuitable for use with many materials including PVCu, Timber, Chipboard, MDF, and other similar types. Zinc coatings prevent oxidation of the protected metal to create a longer lasting finish. It does this by forming a barrier and by acting as a sacrificial anode if this barrier is damaged. Zinc oxide is a fine white dust that (in contrast to iron oxide) does not trigger a breakdown of the substrate’s surface integrity as it is formed. The zinc oxide, if left intact, can act as a barrier to further oxidation, in a way similar to the protection afforded to aluminium and stainless steels by their oxide layers. The Pozidriv screw is similar in appearance to the classic Phillips cross-head, but in fact is very different. The Pozidriv has four additional points of contact, and does not have the rounded corners that the Phillips screw drive has. The biggest advantage it offers is that, when used with the correct tooling in good condition, it does not cam out, allowing great torque to be applied. The Pozidriv screw can easily be distinguished by a line embossed in the screw head at 45° to the slots for the driver. The countersunk head is designed to sink flush with substrates to leave a smooth surface finish. They have single threads, designed to offer higher pull out values and quicker insertion.Specifications: Size: 3.5 x 15mmBox quantity: 200.
These Forgefix General Purpose Pozi Screws with round heads are zinc plated finish for increased durability. They are versatile screws, suitable for use in and with many materials. APPLICATIONIdeal for use in many ironmongery, electrical and plumbing applications.Can be used with various screw cover caps. Zinc coatings prevent oxidation of the protected metal to create a longer lasting finish. It does this by forming a barrier and by acting as a sacrificial anode if this barrier is damaged. Zinc oxide is a fine white dust that (in contrast to iron oxide) does not trigger a breakdown of the substrate’s surface integrity as it is formed. The zinc oxide, if left intact, can act as a barrier to further oxidation, in a way similar to the protection afforded to aluminium and stainless steels by their oxide layers. The Pozidriv screw is similar in appearance to the classic Phillips cross-head, but in fact is very different. The Pozidriv has four additional points of contact, and does not have the rounded corners that the Phillips screw drive has. The biggest advantage it offers is that, when used with the correct tooling in good condition, it does not cam out, allowing great torque to be applied. The Pozidriv screw can easily be distinguished by a line embossed in the screw head at 45° to the slots for the driver. Round headed screws have a flat under head surface making the screw ideal for laying flat on sheet material of all types, reducing deformation. These screws have twin threads to enable an easy start when driving.General Purpose Pozi Screw Round Head TT ZP 1 x 6 Box 200
These Forgefix high-low thread Concrete Frame Screws are Zinc Yellow Passivated for increased resistance to corrosion. They offer a virtually stress free fixing, allowing close to edge applications. They are through-fixing, eliminating the need for marking and re-positioning when fixing batons etc. The Torx compatible head of the screw enables increased torque control. APPLICATION: Extremely popular fixing for window and door frames. Also now used as a versatile fixing for many applications in DIY, Joinery, Plumbing and Electrical trades. The Zinc Yellow Passivation process of electroplating is similar to the 'Galvanised' and 'Zinc Plated' processes but with the addition of a yellow dye. It offers an aesthetically pleasing finish, whilst having excellent resistance to corrosion. By design, Torx compatible head screws resist cam-out much better than Phillips or Slotted screws. Where Phillips heads were designed to cause the driver to cam out, to prevent over-tightening, Torx compatible heads were designed to prevent it and to achieve a desired torque consistently. Torx compatible head sizes are described using the capital letter 'T', followed by a number. A smaller number corresponds to a smaller point-to-point dimension of the screw head. Only the proper driver can drive a specific head size without risk of ruining the driver or screw. High-Low Thread screws have an excellent holding power in wood due to their alternating high and low thread heights.Concrete Frame Screw Torx High-Low Thread ZYP 7.5 x 62mm Bag 10
These Forgefix Multi-Purpose Pozi Screws with countersunk heads have a zinc finish for increased durability. The screws are immensely popular and versatile, and used in all trades including joinery, electrical and plumbing. Also widely used in DIY applications. APPLICATIONSuitable for use with many materials including PVCu, Timber, Chipboard, MDF, and other similar types. Zinc coatings prevent oxidation of the protected metal to create a longer lasting finish. It does this by forming a barrier and by acting as a sacrificial anode if this barrier is damaged. Zinc oxide is a fine white dust that (in contrast to iron oxide) does not trigger a breakdown of the substrate’s surface integrity as it is formed. The zinc oxide, if left intact, can act as a barrier to further oxidation, in a way similar to the protection afforded to aluminium and stainless steels by their oxide layers. The Pozidriv screw is similar in appearance to the classic Phillips cross-head, but in fact is very different. The Pozidriv has four additional points of contact, and does not have the rounded corners that the Phillips screw drive has. The biggest advantage it offers is that, when used with the correct tooling in good condition, it does not cam out, allowing great torque to be applied. The Pozidriv screw can easily be distinguished by a line embossed in the screw head at 45° to the slots for the driver. The countersunk head is designed to sink flush with substrates to leave a smooth surface finish. They have single threads, designed to offer higher pull out values and quicker insertion.Specifications: Size: 5 x 70mm.Box quantity: 100.
These Forgefix Pipe Clips are made from heat resistant polypropylene, designed to withstand the temperature changes in most central heating systems. They are effective with temperatures of up to 100°C. They each come complete with a hardened masonry nail, which is easy to fix and durable. APPLICATION:Used when fitting most types of pipe work. Ensure when fitting that goggles are used. Polypropylene, also known as polypropene, is a thermoplastic polymer used in a wide variety of applications. An addition polymer made from the monomer propylene, it is rugged and unusually resistant to many chemical solvents, bases and acids.Pipe Clip With Masonry Nail 22mm Box 100
The Forgefast Hexagonal/Torx® Compatible Timber Screws are suitable for fixing into soft or hardwood. They have a combination hexagonal head with a deep Torx® compatible insert that reduces cam-out, also provides higher torque levels and a firmer drive. Its super sharp tip gives immediate bite from the very first turn. A patented self-drilling thread removes the need to pre-drill the timber and reduces the probability of splitting, even when screwing close to the edge. Hardened case and core give exceptional strength. Protected by elementech 2000 surface treatment which provides corrosion resistance up to 30 times longer than some standard zinc coated screws. They are highly resistant to pull out, they can flex by up to 35°, reducing likelihood of the screw shearing when used in flexible materials. CE approved for use in load-bearing timber construction. Available in a green or tan treated finish.Forgefast Hexagonal/Torx® Compatible Timber Screws Size: 7 x 200mm.Pack Size: Tub of 50.Finish: Tan elementech 2000.
ForgeFix ForgeFast Wood Screws have a universally accepted, Torx® compatible drive. Their recessed ribs provide improved countersinking and reduced surface dust, and their reinforced countersunk necks improve holding power. The screws have a patented drill and drive thread for reduced splitting of the timber, reduced 'jacking' and spinning of joined timber, increased pull-out and a firmer fix. A sharp point provides faster bite and is capable of piercing 0.8mm steel. The screws have an 'Elementech 400' coating providing an anti-corrosive metal finish, which lasts up to 6 times longer than standard zinc coatings. The coating is environmentally friendly and does not contain Cr6+. It is Salt Spray tested to 400 hours. The screws are suitable for interior use. Every box is supplied with a Torx® compatible bit.Size: 6.0 x 200mm.Box quantity: 100.
VELCRO® Brand Stick On Tape is the easy-to-use alternative to nails and screws. To use, clean and dry both surfaces. Cut tape to length. Peel backing paper and press firmly to surfaces. Allow adhesive 10 minutes to set (or longer for heavier items) before attaching VELCRO® Brand fastening. Supplied as a cut to size roll in white or black. The adhesive reaches maximum strength after 24 hours.
1 x VELCRO® Brand Stick On Tape 20mm x 50cm White
VELCRO® Brand Stick On Coins are easy to use, just clean the surface, peel off the protective backing, and firmly press the sticky pad against the surface. Allow the self adhesive pads to set for 24 hours to achieve full strength. They can hold up to 300g per 20x20mm.These versatile hooked surface adhesive dots can be used as wall sticky pads and so much more, the possibilities are endless.
16 Sets of VELCRO® Brand Stick On Coins 16mm White
VELCRO® Brand Stick On Tape is the easy-to-use alternative to nails and screws. To use, clean and dry both surfaces. Cut tape to length. Peel backing paper and press firmly to surfaces. Allow adhesive 10 minutes to set (or longer for heavier items) before attaching VELCRO® Brand fastening. Supplied as a cut to size roll in white or black. The adhesive reaches maximum strength after 24 hours.
1 x VELCRO® Brand Stick On Tape 20mm x 2.5m Black
VELCRO® Brand Stick On Tape is the easy-to-use alternative to nails and screws. To use, clean and dry both surfaces. Cut tape to length. Peel backing paper and press firmly to surfaces. Allow adhesive 10 minutes to set (or longer for heavier items) before attaching VELCRO® Brand fastening. Supplied as a cut to size roll in white or black. The adhesive reaches maximum strength after 24 hours.
1 x VELCRO® Brand Stick On Tape 20mm x 2.5m White
